Electrical engineering services

This is an important step for any arc flash study that is often overlooked by specifications and sometimes therefore not included within the engineering study. However, at Titan QPS, we understand the importance of this part of any arc flash study and therefore, always include this within our studies. These studies verify that the equipment is rated to interrupt the available fault currents. If for example, the fault current is greater than the interrupting rating of the breaker, bad things can happen, breaker literally catastrophically faults, people can get hurt, cables can get damaged, etc. If this part of your specifications for engineering studies is not contained in your specifications, we highly recommend that you add this to your specs. Regardless, Titan QPS will ensure that this is part of our scope and value to you.

There are many manufactures that will offer their solutions and righfully so. However, at Titan QPS, we have experience working with many qualified OEM’s (Original Equipment Manufactures) and can offer you a solution that truly resolves your problems and within your budget. Harmonics on power systems can reak havoc on your electrical system, causing computer issues, lighting problems, premature equipment failures and the list continues. We have the expertise inhouse to assist you and to provide a solution that truly works.

Do you have a large motor and have you confirmed that you can actually start that motor? Many times, especially on pipe lines, where the utility supply is not very stout, you could run into issues with starting your motors or your utility provider may actually already know that you will have problems starting motors on their lines and will require you to install a VFD, reduced voltage starter, etc. Or if you are experiencing problems with getting motors to run properly, we can assist you. We have extensive experience with motor starting studies and can help you get that motor running reliably!

If you are a manufacturing facility and meet the requirements for predominant usage, your utilities can become tax exempt. This could be a significant cost savings to your bottom line if you are currently paying taxes on your utilities. If you are paying taxes, don’t delay, call us to assist you with completing a predominant usage study for your facility so that you can begin bringing more money to your bottom line.

Are you experiencing power quality problems? Power quality can be defined by many attributes including: light flickering, computer problems, transformers over heating, neutral conductors getting hot, single phasing and the list continues. There are many causes that can create various disturbances. They could be generated within your facility or externally, i.e. created via your utility provider. Regardless, these issues need to be understood before they can be resolved. We have the expertise in house to assist you with any power quality issues or by performing a site wide power systems survey.

If you have older style mechanical protective relays and wish to upgrade these to new solid state protective relays, we have considerable experience on this front and can offer many solutions from many vendors. There are a lot of manufactures of protective relays out there today and we have experience that can match your solution at a very competitive price. Regardless if you have transmission line protection schemes, differential schemes, feeder protection, generator protection, we can help you with upgrading your systems to modern protective relays. The benefits of upgrading your protective relays are large so please contact us for more information.

The basis of calculations for arc flash hazard levels, equipment evaluation and other power system studies is the calculation of the short circuit values. The short circuit values are the maximum, i.e. worst case current that could flow during a fault on your power system. It is critical that these values be determined correctly not only for the calculations of the arc flash hazards, equipment evaluation, etc. but so that you don’t over emphasize the hazards. Many companies assume a worst case short circuit at the utility service and this is not a good engineering practice in that it could seriously overestimate the arc flash hazards in your facility, etc. Titan QPS has the experience to assist you with correctly determining your short circuit values within your system and further to properly run additional power systems studies that rely on this data as the basis.

Have you ever had a problem that you could not identify that created absolute havoc on your system? There are many causes for transient stability issues and the first is to identify the root cause of the problem then provide solutions. Many of today’s advanced relays can monitor and record transient issues within your power system if they are set up correctly. Regardless, we have the knowledge and expertise to assist you with identifying your source of transient issues and correcting those problems.

Whether you are building a new substation, have an existing substation, experiening grounding problems, etc. we are your solution. We utilize SKM ground mat software to assist with the design of your ground grid. We have extensive experience with troubleshooting and testing various grounding systems. If you are experiencing problems with your ground grid or need to have it tested and evaluated by an experienced certified Technician whom is also a Professional Engineer, please give us an opportunity to assist you.

Normally when new systems are being designed, load flow and voltage drop studies are conducted to ensure that a system is designed properly, i.e. that cables are sized appropriately, that you do not have to much system impedance that can create significant voltage drop issues, etc. These are pretty extensive studies for we have to take into account all loads, cable sizing, etc. The output report confirms that your system is designed correctly and flags any problems that can be seen by the study. Please contact us if you have a need for a load flow / voltage drop study or if you are experiencing voltage stability problems.

If you are a utility, Co-Op, power plant owner or other entity that has to comply with the NERC and FERC reliability standards, we can assist you with your plan development, training requirements, maintenance plan development – PRC-005, mitigation and testing services. Our founder has hosted many NERC and FERC conferences and has the expertise to assist you with your compliance. We can also assist you with your PRC-005 requirements from testing your protective relays, testing your DC trip schemes, testing your battery systems and other areas of compliance.

Are you paying a power factor and/or demand charge on your utility bill? We have experience assisting customers with utility power savings by implementing power factor correction schemes to in crease their power factor at the utilities point of coupling which can also aid in voltage stability, increased systems capacity with your plant and other benefits. If you are paying a power factor penalty, please contact us for an evaluation of your facility to determine if implementing a power factor bank is beneficial to you and your pocket book.

If you are looking for an experienced company that has experience with designing your protective relay schemes, performing maintenance testing, acceptance testing, etc. on your protective relays we are your answer. There are many types of protective relays and we have experience testing and designing systems with many manufactures so therefore we are not limited on our offering to you. We offer a solution that fits your needs and meets your requirements, regardless if you have a preferred manufactures protective relay that you wish to utilize or are open to other manufactures protective relays. We are your solution for protective relays. Please contact us for any protective relay needs that your company may have for we have significant experience on this front.

Are you experiencing issues within your facility concerning breakers tripping when they are not supposed to trip? Are your upstream breakers tripping before your feeder breakers? There is an art and science to performing these studies to ensure that when faults occur that the fault is isolated to the minimum amount of your system, i.e. that it isolates at the fault and not falsely to other upstream devices. This creates significant problems if there are mis-coordination with your systems, lights could go out, Tech’s troubleshoot the wrong areas and the list continues. We have examples of reports that we could send to prove that the value that Titan QPS provides on this front is truly not matched by our competition. Hire a company that has experience and that is Titan QPS.

If you have .pdf copies of drawings and need to have these converted over to updated AutoCAD format, we can assist you. If you simply need for your drawings to be updated via red-lines in the field, then updated electronically, we can assist you. We have experience drafting: One-lines, three-lines, wiring schematics, DC schematics, point-to-point diagrams and the list continues.